Properties of self-curing and self-cooling eco-friendly novel green cement-based mortar
DOI:
https://doi.org/10.7764/RDLC.23.2.436Keywords:
Self-cooling, self-curing, eco-friendly, direct current, green mortar.Abstract
In this study, mullein plant (MP) (Verbascum Thapsus) was replaced with cement at a dosage of 300 (the amount of cement in mortar for producing 1 m3 mortar) in cement-based mortars at different weight ratios (0%, 1.5%, 3%, 4.5% and 6%). To investigate the impact of MP on the hydration (internal) temperature and the formation time of hydration products in mortars, the mortars' interior temperature and moisture ratios were measured and recorded every minute for one day. It was concluded that the MP had a high-water absorption capacity and delayed the initial and final setting times. The optimum ratio of MP as a replacement for cement was found to be 1.5%. The study also investigated the effects of direct current (DC) application on fresh mortars (both with and without MP). The results showed that the 7-day mechanical strength of the reference mortars exhibited a significant increase with the application of DC. Previous studies have not explored the use of MP in cementitious composite materials. This study concluded that adding a specific amount of MP to cement-based materials can provide self-curing and self-cooling properties. This research is critical for water conservation as it develops a novel self-curing method.
Downloads
References
ACI (308-213) R-13 (2022). Report on Internally Cured Concrete using Pre-Wetted Absorptive Lightweight Aggregate. American Concrete Institute.
ASTM C 1012-04, Standard test method for length change of hydraulic-cement mortars exposed to a sulfate solution, ASTM International, 2004. www.astm.org.
ASTM C305-20, Standard practice for mechanical mixing of hydraulic cement pastes and mortars of plastic consistency, ASTM International, West Conshohocken, PA, 2020. www.astm.org.
ASTM C348. Standard Test Method for Flexural Strength of Hydraulic-Cement. ASTM Int West Conshohocken, PA. 2014. www.astm.org.
ASTM D570-98, Standard Test Method for Water Absorption, ASTM International, West Conshohocken, PA, 2022. www.astm.org.
Bashandy, A.A. (2015). Performance of self-curing concrete at elevated temperatures, Indian Journal of Engineering and Materials Science, 22, 93-104. http://nopr.niscpr.res.in/handle/123456789/31251.
Bashandy, A.A., Meleka, N.N., Hamad, M.M. (2017). Comparative study on the using of PEG and PAM as curing agents for self-curing concrete. Chal-lenge Journal of Concrete Research Letters, 8(1), 1–10. https://doi.org/10.20528/cjcrl.2017.01.001.
Bentz, D.P., Lura, P. Roberts, J.W. (2005). Mixture proportioning for internal curing. Reprinted from the Concrete International, 27(2), 35-40.
Bentz, D.P., Weiss, W.J. (2011). Internal curing: A 2010 state-of-the-art review, U.S. Department of Commerce, NISTIR 7765. https://doi.org/10.6028/NIST.IR.7765.
Bilek, V., Kersner, Z., Schmid, P., Mosler, T. (2002). The possibility of self-curing concrete. Proceedings of the International Conference of Innovations and Developments in Concrete Materials and Construction, 51-60.
BS EN 12390-2, Testing hardened concrete making and curing specimens for strength tests, 2019.
BS EN 196-3, Methods of testing cement, 2016.
Chand, M.S.R., Giri, P.S.N.R., Kumar, P.R., Kumar, G.R., Raveena, C. (2016). Effect of self-curing chemicals in self-compacting mortars. Construction and Building Materials, 107, 356-364. https://doi.org/10.1016/j.conbuildmat.2016.01.018.
Concrete Core Testing for Strength, Technical Report No:11, The Concrete Society, London, 1976.
Duguid, A., Scherer, G.W. (2010). Degradation of oil well cement due to exposure to carbonated brine. International Journal of Greenhouse Gas Control, 4, 546-560. https://doi.org/10.1016/j.ijggc.2009.11.001.
El-Dieb, A. S., & El-Maaddawy, T. A. (2020). Performance of self-curing concrete as affected by different curing regimes. Advances in Concrete Construc-tion, 9(1), 33-41. https://doi.org/10.12989/acc.2020.9.1.033.
El-Dieb, A.S. (2007). Self-curing concrete: Water retention, hydration and moisture transport. Construction and Building Materials, 21, 1282-1287. https://doi.org/10.1016/j.conbuildmat.2006.02.007.
Fabre, S., Lesaignoux, A., Olioso, A., Briotte, X. (2011). Influence of water content on spectral reflectance of leaves in the in the 3–15-µm Domain. IEEE Geoscience and Remote Sensing Letters, 8(1), 143-147. https://doi.org/10.1109/LGRS.2010.2053518.
Ghiasvand, H., Bastami, M., Farokhzad, R. (2022). Enhancing the internal curing process of self-compacting concrete containing lightweight aggregate and chemical additives. European Journal of Environmental and Civil Engineering, 1-19. https://doi.org/10.1080/19648189.2022.2026824.
Hammond, G.P., Jones, C.I. (2008). Embodied energy and carbon in construction materials. Proceedings of the Institution of Civil Engineers Energy, 161(2), 87–98. https://doi.org/10.1680/ener.2008.161.2.87.
Hocaoglu, I. (2021). Self-heating mortars with using graphene oxide and increasing CSH gel formation with the direct current application. Revista De La Construcción. Journal of Construction, 20(3), 559–575. https://doi.org/10.7764/RDLC.20.3.559.
Hocaoğlu, I. (2022). Investigation of the effect of current in zeolite-graphene oxide additives of mortar and development of a novel method for determin-ing the setting time. Journal of Building Engineering, 46, 103803. https://doi.org/10.1016/j.jobe.2021.103803.
Hocaoğlu, I. (2022). Self-cooling mortar production with zinc oxide nanoparticles additive and investigation of the DC application when early-age hydra-tion. European Journal of Environmental and Civil Engineering. https://doi.org/10.1080/19648189.2022.2144464.
Hocaoğlu, I. (2023). Investigation of the effects of dosage and direct current intensity in new generation mortars with graphene oxide additives. Journal of the Faculty of Engineering and Architecture of Gazi University, 38(1), 421-434. https://doi.org/10.17341/gazimmfd.940271.
Hocaoğlu, I (2024). A novel cost-effective method for self-estimation of crack occur time by piezoelectric measurement of glass powder-modified ce-mentitious mortar. Journal of Building Engineering, 86, 108967. https://doi.org/10.1016/j.jobe.2024.108967.
Hossain, M.U., Poon, C.S., Lob, I.M.C., Cheng, J.C.P. (2017). Comparative LCA on using waste materials in the cement industry: a Hong Kong case study, Resources Conservation and Recycling, 120, 199-208. https://doi.org/10.1016/j.resconrec.2016.12.012.
Hu, C. (2014). Microstructure and mechanical properties of fly ash blended cement pastes. Construction and Building Materials, 73, 618-625. https://doi.org/10.1016/j.conbuildmat.2014.10.009.
Jaya, R.P., Hainin, M.R., Wan, I.M.H., Nazri, F.M., Arshad, M.F., Muthusamy, K. (2018). Physical and chemical properties of rice husk ash concrete under seawater, International Journal of Integrated Engineering, 10, 165-168. http://umpir.ump.edu.my/id/eprint/22519.
Jieting, X., Xiao, Q., Zhenying, H., Yongkang, L., Ben, L., Zhengzhuan, X. (2022). Effect of superabsorbent polymer (SAP) internal curing agent on car-bonation resistance and hydration performance of cement concrete. Advances in Materials Science and Engineering, 3485373, 1-13. https://doi.org/10.1155/2022/3485373.
Kamal, M. M., Safan, M.A., Bashandy, A.A., Khalil, A.M. (2018). Experimental investigation on the behavior of normal strength and high strength self-curing self-compacting concrete. Journal of Building Engineering, 16, 79-93, https://doi.org/10.1016/j.jobe.2017.12.012.
Kifayatullah, Q., Shah, M.T., Arfan, M. (2001). Biogeochemical and environmental study of the chromite-rich ultramafic terrain of Malakand area Paki-stan. Environmental Geology, 40, 1482-1487. https://doi.org/10.1007/s002540100374.
Kosmatka, S.H., Voigt, G., Taylor, P. (2016). Integrated materials and construction practices for concrete pavement: a state-of-the-practice manual. Center for Translation Research and Education, Iowa State University, 69-104. https://intrans.iastate.edu/app/uploads/2019/05/IMCP_manual.pdf.
Kumar, M., Bansal, M., Garg, R. (2020). An overview of beneficiary aspects of zinc oxide nanoparticles on performance of cement composites. Materials today: Proceedings, 43, 892-898. https://doi.org/10.1016/j.matpr.2020.07.215.
Kunther, W., Ferreiro, S., Skibsted, J. (2017). Influence of the Ca/Si ratio on the compressive strength of cementitious calcium-silicate-hydrate binders, Journal of Materials Chemistry A. 5(33), 401-412. https://doi.org/10.1039/C7TA06104H.
Kutchko, B.G., Strazisar, B.R., Dzombak, D.A., Lowry, G.V., Thaulow, N. (2007). Degradation of Well Cement by CO2 under Geologic Sequestration Conditions, Environmental Science and Technology, 41(13), 4787. https://doi.org/10.1021/es062828c.
Lokeshwari, M., Pavan, B.R., Bandakli, S.R., Tarun, P., Sachin, Kumar, V. (2021). A review on self-curing concrete. Materials today: Proceedings, 43(2), 2259-2264. https://doi.org/10.1016/j.matpr.2020.12.859
Mahek, A., Tanveer, N., Jayalakshmi, S. (2011). Pharmacognostical standardisation and physico-chemical valuations of leaves of Verbascum Thapsus Linn. International Journal of Drug Development and Research, 3(1), 334-340.
Purnell, P., Black, L. (2012). Embodied carbon dioxide in concrete: variation with common mix design parameters. Cement and Concrete Research 42, 874-877. https://doi.org/10.1016/j.cemconres.2012.02.005.
Ramalingam, V., Ramesh, K., Duraipandi, M.U.J., Kuppusamy, S. (2022). Water absorbing polymer balls as internal water curing agent in concrete to support hydration reaction. Revista De La Construcción. Journal of Construction, 21(1), 83–92. https://doi.org/10.7764/RDLC.21.1.83
Ravikumar, M.S., Selvamony, C., Kannan, S.U., Basil, G.S. (2011). Self-compacted self-curing kiln ash concrete. International Journal on Design and Manufacturing Technologies. 5(1), 63.
Riaza, M., Zia-Ul-Haq, M., Jaafar, H.Z.E. (2013). Common mullein, pharmacological and chemical aspects, Revista Brasileira Farmacogn, 23, 948-959, https://doi.org/10.1590/S0102-695X2013000600012.
Salem, T.M. (2002). Electrical conductivity and rheological properties of ordinary portland cement-silica fume and calcium hydroxide-silica fume pastes. Cement and Concrete Research, 32, 1473-1481. https://doi.org/10.1016/S0008-8846(02)00809-8.
Scherer, G.W., Huet, B. (2009). Carbonation of wellbore cement by CO2 diffusion from caprock. International Journal of Greenhouse Gas Control, 3(40), 731-735. https://doi.org/10.1016/j.ijggc.2009.08.002.
Seongwoo, G., Young, C.C., Myoungsu, S. (2022). Internal curing of cement composites using kenaf cellulose microfibers. Journal of Building Engineering 47, 103867. https://doi.org/10.1016/j.jobe.2021.103867.
Shah, M.T., Kifayattullah, Q., Arfan, M. (2004). Pedo and biogeochemical study of zinc-lead deposits of the Besham area, northern Pakistan: its implica-tion in mineral exploration and environmental degradation. Environmental Geology, 45, 544-549. https://doi.org/10.1007/s00254-003-0909-8.
Tatli, I.I. Akdemir, Z.S. (2016). Traditional uses and biological activities of verbascum species. Fabad Journal of Pharmaceutical Sciences, 31, 85-96.
Topçu, I.B., Sofuoğlu, T. (2021). Properties of geopolymers produced with sugar press filter waste and fly ash under certain curing conditions. Journal of Building Engineering, 44, 102938. https://doi.org/10.1016/j.jobe.2021.102938.
TS EN 12390-7, Concrete-hardened concrete tests - Part 7: Determination of hardened concrete density, 2010. Turkish Standards Institute, Ankara, Turkey.
TS EN 197-1, Cement. Composition, specifications and conformity criteria for common cements, European Standard, 2011.
Turker, A.U., Camper, N.D. (2002). Biological activity of common mullein, a medicinal plant. Journal of Ethnopharmacology, 82, 117-125. https://doi.org/10.1016/s0378-8741(02)00186-1.
Turker, A.U., Gurel, E. (2005). Common mullein (Verbascum thapsus L.): recent advances in research. Phytother Research 19, 733-739. https://doi.org/10.1002/ptr.1653.
Vyawahare, M. R., Naik, B. (2014). Comparative study on durability of self cured SCC and normally cured SCC, Materials Science, Engineering, 3(8), 1201-1208.
Xiao, R., Ma, Y., Jiang, X., Zhang, M., Zhang, Y., Wang, Y., Huang, B., He, Q. (2020). Strength, microstructure, efflorescence behavior and environmental impacts of waste glass geopolymers cured at ambient temperature. Journal of Cleaner Production, 252, 119610. https://doi.org/10.1016/j.jclepro.2019.119610.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 Ismail Hocaoglu, İlker Bekir Topçu
![Creative Commons License](http://i.creativecommons.org/l/by-nc-nd/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.